Hold the base unit firmly and press the release tabs on the sides of the stand to detach the base unit.ģ. Turn the phone so that the front faces away from you.Ģ. To tilt your telephone for better viewing:ġ. The stand built into your phone tilts to give you a better view of the keys. Disconnecting the headset at the jack or at the quick-disconnect plug restores handset operation. Installation will disable your handset microphone. IMPORTANT NOTE FOR HEADSET USERS: Mitel Headsets with Feature Control Switch must be installed in the dedicated headset jack (the jack on the back of the phone). Because continuous exposure to loud sounds can contribute to hearing loss, keep the volume at a moderate level. Your phone has a control for adjusting the volume of the handset receiver or headset. See the section on headset usage elsewhere in this guide for more information. If you use your phone a lot, you may find it more comfortable to use a headset. Prolonged use of the handset can lead to neck, shoulder, or back discomfort, especially if you cradle the handset between your ear and shoulder. Until the switch to the primary system is complete. If your phone is idle and switched to the secondary system, you'll see a flashing rectangle on the display. Normal operation resumes when your phone switches back to the primary system. If your phone switches to the secondary system while your speaker or handset is muted (that is, while the MUTE light is on), the call remains muted until you hang up. The keys and most features begin working normally again after you hang up. The call continues but some of the keys and features on your phone function differently. If during a call, you hear two beeps repeated every 20 seconds it means that your phone is switching to a secondary 3300 ICP system. Use the slot behind the plastic cover at the bottom of the phone to remove/insert the designation card. Write the name (speed call, feature or line appearance) of the Personal keys that you program on the designation card (use the side of the card with the textboxes provided). On the 5212 IP Phone, the bottom left personal key is always your Prime Line key. On a 5224 IP Phone, theīottom right personal key is always your Prime Line Provides keys that can be programmed as speedĬall keys, feature keys, or line appearance keys,Īccording to your communication needs. Mailbox and flashes to notify you of messages (MESSAGE) : provides access to your voice (TRANS/CONF) : initiates a call transfer orĮstablishes a three–party conference call. (HOLD) : places the current call on hold. Phone, eliminates any input and returns to the The call, and, when you are programming the Z (CANCEL) : ends a call when pressed during Navigating through Superkey menu options, press (SUPERKEY) : provides access to menus for Give you access to the following phone functions: Or handsfree microphone off during a call. Temporarily turn your phone's handset, headset Z (MUTE) enables Mute, which allows you to Provide the following audio control capability:Ĭontrol for the ringer, handset, and handsfree Softkeys enable you to easily view andįlashes to signal an incoming call and to indicate a Modes of the operation and the menu currentlyĭisplayed. Without softkeys, see "Selecting Menu Options"Ĭontext-sensitive keys change depending on the Information on selecting menu options with or Using the Superkey menu interface, prompts andįeature information appear on the display screen. Selecting and using phone features, accessing your Provides a two–line, 20–character liquid crystalĭisplay (LCD) viewing area that assists you in Only the administrator can program line appearances. You can program speed call keys from your phone. Your administrator can also program feature keys. You can program feature keys from your phone. The personal key on the bottom (left on 5212, right on 5224) is always your Prime Line the remaining personal keys can be programmed as: The 5224 IP Phone can be used as an ACD Agent Phone or a Teleworker phone. The 5224 IP Phone also supports modules such as the Line Interface Module, 5310 IP Conference Unit, and the 12 and 48 Buttom Programmable Key Modules. The 52 IP Phones support Mitel Call Control (MiNet) protocols and session initiated protocols (SIP). Both phones provide ten fixed feature keys for convenient access to features such as Conferencing, Redial, and many customizable user settings. The 5212 IP Phone offers 12 programmable keys, and the 5224 IP Phone offers 24 programmable keys for one-touch feature access. Each features a back-lit liquid crystal display (LCD) screen, display-assisted access to features, on-hook dialing and off-hook voice announce with handsfree answerback, and a large ring/message indicator. The Mitel 52 IP Phones are full-feature, dual port, dual mode telephones that provide voice communication over an IP network.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |